Search found 45 matches

by juansh2385
Tue Mar 25, 2014 6:01 pm
Forum: Signal Interceptor
Topic: Signal Interceptor now available
Replies: 7
Views: 11114

Re: Signal Interceptor now available

Jean do you plan on doing more i was browsing your web store and notice they are out of stock. I intend to use one of this to diagnose wiring problems in the car when the units past stim testing but are not functioning adequately in the car normally because of wiring issues.
by juansh2385
Tue Feb 19, 2013 8:48 am
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

Jean is official I made it functional with you board but is far from optimal. I improve the result hacking a little bit the code. I not sure if you knew but the reason that it did not work as intended is because the throttler plate is controlled by a servo motor. I am going to take the idea of anoth...
by juansh2385
Thu Feb 14, 2013 11:32 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

yes I installed s12 the one that is beside r57 trust me it did not work. As for the code I expected that much do not worry I was reporting back as promise.

Juan
by juansh2385
Thu Feb 14, 2013 10:32 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

Hi Jean reporting back as promise first even though the factory pc controls this valve at 500hz i could only make it stop homing 15616hz I use 256 jumper and a 61 frequency from the ms. Now some bad News I know you recommend using 12v from the battery but I didn't have spare pins so I use s12 spot i...
by juansh2385
Thu Feb 14, 2013 1:44 am
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

sorry did not express that question correctly. I meant what the maximum recommend en valve output frequency from the board. at 500hz is still buzing and i have no control over it
by juansh2385
Thu Feb 14, 2013 12:15 am
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

what is the maximum output frequency recommended for the valve?
by juansh2385
Wed Feb 13, 2013 7:29 am
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

Last Question I hope. I am going to use Fidle as the in pin. Where do I take the signal of the cpu before (directly to cpu pin) or after R19?
by juansh2385
Tue Feb 12, 2013 10:21 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

Quick reply as always great support. May I suggest that you should clarify this in the page. I am not sure if I am the only one with the doubt but I think is a good idea to clarify.
by juansh2385
Tue Feb 12, 2013 10:18 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

ok thanks
by juansh2385
Tue Feb 12, 2013 9:07 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

I have a silly question jean in the picture of your page that explains what jumper I need to made to select the multiplier where is located the cpu in that picture left or right? I am having trouble selecting the right jumpers because I can not know what reference I can use to know the position that...
by juansh2385
Sun Feb 03, 2013 10:23 pm
Forum: New Boards
Topic: Ruggedized ECU
Replies: 66
Views: 82314

Re: Ruggedized ECU

Hi Jean I was wondering what happen with this?
by juansh2385
Sun Feb 03, 2013 10:14 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

Re: audi 1.8t idle valve

Well I analyze the stock signal and is about 500hz but ms2 idle control is not really happy with that kind of frequency I am willing to try the board is not that expensive :D . I think you will receive the order this week is it 26 usd ship to puerto rico too? any ways I'll keep you updated. Juan
by juansh2385
Sun Feb 03, 2013 9:37 pm
Forum: PWM Converter
Topic: audi 1.8t idle valve
Replies: 17
Views: 13630

audi 1.8t idle valve

HI Jean I am trying to take control of and 1.8t audi idle in this case there is no valve in the car the throttle have and electric motor apparently pwm that opens the plate and make the car idle. I am planing on using one of your pwm converter to amplify the ms pwm signal. I was wondering are you aw...
by juansh2385
Thu Jun 28, 2012 3:56 pm
Forum: 4-Channel Driver
Topic: vnd problems
Replies: 5
Views: 3043

Re: vnd problems

Jean thanks for the advice,

This car is from a client and he does not want take any chance so we already order the original parts the car is down so there is no rush now, and yes we are going to verify everything else as well injectors and all the fuel delivery components.

Thanks again

Juan
by juansh2385
Wed Jun 27, 2012 5:08 pm
Forum: 4-Channel Driver
Topic: vnd problems
Replies: 5
Views: 3043

Re: vnd problems

hey Jean, So I wanted to give and updated and maybe a warning for some reason the car that we made the mods above for the 4 channel board with different component it down for the moment. It lean out in cylinder 4 at 20 psi so you can imagine. what we notice that is strange is that it happened after ...
by juansh2385
Mon Jun 11, 2012 12:43 am
Forum: 4-Channel Driver
Topic: vnd problems
Replies: 5
Views: 3043

Re: vnd problems

Great

Thanks
by juansh2385
Sun Jun 10, 2012 3:45 pm
Forum: 4-Channel Driver
Topic: vnd problems
Replies: 5
Views: 3043

vnd problems

Hi jean In one of the boards that I purchase from you for a client i had mosfet problems with 2 of them. I am not using the board to hold the bip and I live in puerto rico so is hard to get vnd mosfet type here. I bouth 4 irlz44n from a local store installed them in the bip section and with jumper i...
by juansh2385
Thu Feb 16, 2012 4:57 pm
Forum: Peak&Hold Driver
Topic: Sequential Peak & hold with Microsquirt
Replies: 4
Views: 2434

Re: Sequential Peak & hold with Microsquirt

hey jean,is it possible to connect directly to the cpu pin?
by juansh2385
Wed Feb 15, 2012 6:16 pm
Forum: Peak&Hold Driver
Topic: Hello I appear (solved )
Replies: 26
Views: 16251

Re: Hello I appear

Jean,

Jorge lost his copy of the schematics can you contact him in a pm or something or should I tell him to contact you directly?
by juansh2385
Wed Feb 15, 2012 8:27 am
Forum: Peak&Hold Driver
Topic: Hello I appear (solved )
Replies: 26
Views: 16251

Re: Hello I appear

I will ask him again but apparently he lost his or at least that was what I understood that happened
.