Search found 13 matches

by Kertwerks
Thu Jun 18, 2015 10:47 am
Forum: General
Topic: IMPORTANT: Activity slow down
Replies: 15
Views: 117237

Re: IMPORTANT: Activity slow down

Hi Jean, Hope things are looking up for you and yours. I am in critical need of 4 P&H PCB's, ECU case mounted units. I have orders for 2 now and have used the 2 I had on the shelf. Could you please shoot me an e-mail off line at your earliest convenience. Thanks and prayers are with you and yours, K...
by Kertwerks
Tue Mar 19, 2013 11:35 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Jean, I'm having some issues starting the system with the sequential driver. Seems like there isn't enough fuel getting to the engine. I ran the system on my test table and the injectors are firing in the correct order. I've cross wired a batch fire ECU that I will try to start the car with today. O...
by Kertwerks
Thu Feb 21, 2013 3:56 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Jean,
The fuel pump is grounded activating the pump at power up for 3 sec.
How is this going to resolve my problem?
Why is it only affected when powering both banks at the same time?
And just as mysteriously the problem vanished.
Is this related to a power up spike?
by Kertwerks
Thu Feb 21, 2013 3:20 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Jean,
Something weird happened this morning.
The P&H PCB is continually fireing my injectors on power up.
If I pull bank AorB fuse and power up then replace the bank AorB fuse it works ok.
If I power it up with both fuses in place it continually fires all 4 injectors.
Please advise,
Kurt
by Kertwerks
Wed Feb 13, 2013 1:08 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Hi Jean, Board arrived last week, 3 weeks, damn :( . Installed and functioning correctly :D :D 8-) . Here are some short vid's of it running on the test bench. http://www.flickr.com/photos/kertwerks/8463096852/in/set-72157632734058675/ http://www.flickr.com/photos/kertwerks/8468046897/in/set-7215763...
by Kertwerks
Sat Jan 26, 2013 10:02 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Hi Jean,
Just a little curious abou the P&H board.
Have not recieved it yet and it's been more then a week.
Kurt
by Kertwerks
Tue Jan 22, 2013 1:15 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Hi Jean, Looking at the assambly sheets I have another question. My intention was to wire the 1&2 injectors thru the normal DB37 outputs and the 3&4 outputs out Spr3&4 on the DB37 connector. To do this can I just remove Q1 and Q5 and run the injector drivers from the P&H pcb thru these as shown here...
by Kertwerks
Thu Jan 17, 2013 7:13 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

OK, Thanks
Kurt
by Kertwerks
Thu Jan 17, 2013 6:43 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Additionally, on a 3.0 PCB is it as shown her for component removal?
http://jbperf.com./sequential/index.html#v3conn
R21,C20,C21,R22,R23,Y1,C24,C25..

Are there any additional instructions I should review before the unit arrives?
Kurt
by Kertwerks
Thu Jan 17, 2013 6:35 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Great, ordered the P&H unit Sunday. Looking forward to recieving it. I have a full bench system set up with o-scope, p-supply, dist drive system and enough eletronics and mechanical knowledge to be dangerous. If your kit works out as well as I've read they do it may be the last piece of the puzzle t...
by Kertwerks
Thu Jan 17, 2013 5:41 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Sorry I mis-spoke, The wheel has 7 magnets 1 missing.
1 missing tooth for every 2 crank rotations.
Kurt
by Kertwerks
Thu Jan 17, 2013 5:16 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Re: Hello Group

Jean, The Bosch D-jet system triggered the FI system via a 2nd&3rd set of points mounted on a plate below the mechanical advance plate. The points were trigger by a cam on the distributor shaft. I remove the Mecahnical advance plate and press a 8-1-1 wheel (2/10 thick aluminum disc with 7, 1/8" x 1/...
by Kertwerks
Thu Jan 17, 2013 3:29 pm
Forum: Introduce yourself
Topic: Hello Group
Replies: 21
Views: 8744

Hello Group

Hello, My name is Kurt. I'm currently building MSII systems for classic Volvo's 1800's w/Bosch D-jet. I have 5 systems installed 2 w/relay boards 3 w/Stealth systems. What I've tried to achive is a Stealth system that is hidden within the original D-jet components. I've made a 8-1-1 trigger wheel th...