Search found 18 matches

by MS2tester
Wed Oct 03, 2018 1:59 pm
Forum: New Boards
Topic: CAN-EGT+
Replies: 67
Views: 56862

Re: CAN-EGT+

i have been reading up on the ability of the tinyOX to connect to tunerstudio or msdash through the CAN bus or at-least displaying data from the CAN bus connected devices like MS2 or MS3 would the diyautotune CAN EGT be able to do the same? i see a lot of questions from people who want to run a dedi...
by MS2tester
Thu Nov 10, 2016 8:10 am
Forum: I/O Extender
Topic: TinyIOx
Replies: 142
Views: 159096

Re: TinyIOx

was one other thing i was thinking about! having the relais in parallel with the coil negative side trigger keeping the coil energized therefore not sparking during wheel spin should it release before top dead center and before the normal spark would occur coil energizing would be continued by the o...
by MS2tester
Wed Nov 09, 2016 8:24 am
Forum: I/O Extender
Topic: TinyIOx
Replies: 142
Views: 159096

Re: TinyIOx

grounding the high voltage output maybe?
by MS2tester
Tue Nov 08, 2016 8:37 am
Forum: I/O Extender
Topic: TinyIOx
Replies: 142
Views: 159096

Re: TinyIOx

would it be an idea to add a form of traction control to the tiny code ? i was thinking something like an active condition versus an active condition say you have PwmA input versus PwmC input the condition needs to be equal = with a hysterix of 200 pulses in this case? or cut digital out relais with...
by MS2tester
Sun Oct 25, 2015 10:09 am
Forum: I/O Extender
Topic: Re: CAN-EGT firmware upgrade
Replies: 7
Views: 3002

Re: CAN-EGT firmware upgrade

looks a lot better :)
by MS2tester
Sat Oct 24, 2015 5:54 am
Forum: I/O Extender
Topic: Msdroid can egt stand alone
Replies: 6
Views: 4014

Re: Msdroid can egt stand alone

well again this time with the proper settings
by MS2tester
Sat Oct 24, 2015 5:47 am
Forum: I/O Extender
Topic: Re: CAN-EGT firmware upgrade
Replies: 7
Views: 3002

Re: CAN-EGT firmware upgrade

well that did the trick
although i must say a pair of standard boot jumpers would be nice
people could simply held a small screw driver between them without touching the board :ugeek:
by MS2tester
Fri Oct 23, 2015 3:53 pm
Forum: I/O Extender
Topic: Re: CAN-EGT firmware upgrade
Replies: 7
Views: 3002

Re: Port scanner

just to make sure
it,s the 2 pinholes nex to BOOT on the silkscreen
i guess i will have to soldering some pins
think this won,t be the last time
by MS2tester
Fri Oct 23, 2015 3:00 pm
Forum: I/O Extender
Topic: Re: CAN-EGT firmware upgrade
Replies: 7
Views: 3002

Re: Port scanner

Because it does not respond to anything anymore Msdroid does not give a signature And it will not connect to tunerstudio I tried hooking up the LC1 to the port under msdroid It did not give any readings I then enabled serial pass through Burned and cycled power After that it did not respond anymore ...
by MS2tester
Fri Oct 23, 2015 1:16 pm
Forum: I/O Extender
Topic: Re: CAN-EGT firmware upgrade
Replies: 7
Views: 3002

Re: CAN-EGT firmware upgrade

ok i royaly screwed up my can egt
first tried the diyautotune can firmware

then tried to use port scanner 1.2

it should be com6 tried it but no luck
by MS2tester
Thu Oct 22, 2015 3:44 pm
Forum: I/O Extender
Topic: Msdroid can egt stand alone
Replies: 6
Views: 4014

Re: Msdroid can egt stand alone

the serial ini did the trick :lol: still have to check the LC1 pass through but will have to dig for the spare one thing tho it will log but the log will not show data is shall make a port for that in msdroid but i feel this will already be a great help are there any plans to add support for somethi...
by MS2tester
Thu Oct 22, 2015 2:02 pm
Forum: I/O Extender
Topic: Msdroid can egt stand alone
Replies: 6
Views: 4014

Re: Msdroid can egt stand alone

i have the can egt ini in the ini folder
i even named a second one with the signature name
but it does not seem to matter same error
by MS2tester
Thu Oct 08, 2015 9:58 pm
Forum: I/O Extender
Topic: Msdroid can egt stand alone
Replies: 6
Views: 4014

Msdroid can egt stand alone

I have found a post in msdroid in wich you state that msdroid is able to read tinyox and the can egt Did you mean msdroid can read this without being connected to a megasquirt? The reason i am asking this Is that i know some People with classic cars Who i see struggeling with tuning their carb set u...
by MS2tester
Tue Feb 24, 2015 7:07 am
Forum: Peak&Hold Driver
Topic: evinrude ETEC injector
Replies: 8
Views: 4842

Re: evinrude ETEC injector

maybe it,s a little less complicated as originally thought but still quite a component build :roll: i,m not an electronics expert but the ecm seems to control switch 318 for the reverse signal pulse the injector runs on the 55 volt if instead of having switch 318 controlled by the ecu connect a zene...
by MS2tester
Mon Feb 23, 2015 3:32 pm
Forum: Peak&Hold Driver
Topic: evinrude ETEC injector
Replies: 8
Views: 4842

Re: evinrude ETEC injector

i think i will focus on the mercury optimax engine for now :geek:
by MS2tester
Mon Feb 23, 2015 2:27 pm
Forum: Peak&Hold Driver
Topic: evinrude ETEC injector
Replies: 8
Views: 4842

Re: evinrude ETEC injector

the original ecu seems to be very advanced
being able to send reverse pulses :roll:

i did manage to find something in a thesis paper
https://drive.google.com/file/d/0B2M1nE ... sp=sharing
by MS2tester
Mon Feb 23, 2015 12:01 pm
Forum: Peak&Hold Driver
Topic: evinrude ETEC injector
Replies: 8
Views: 4842

Re: evinrude ETEC injector

the original ecu is water cooled
i just thought of the fuel running through the injector
it could be designed this way to cool the injector coil
so i guess the driver could be a heavy duty mosfet against a water cooled body?
by MS2tester
Mon Feb 23, 2015 8:14 am
Forum: Peak&Hold Driver
Topic: evinrude ETEC injector
Replies: 8
Views: 4842

evinrude ETEC injector

this is an idea i am playing with since looking at the schematic the injector driver seems to be isolated from the rest of the electrical system the ETEC injector is a 2 to 3 ohm injector which operates at 55 volt the 33 volt zener? new value? = will probably have to be substituted but other than th...