Mega Squirt II Programmable EMS, PC3.0

[jrods2]

Finished JimStim & every thing works as required. Starting MG-II assembly, Are there better assembly instructions(like the JimStim) than the one at www.megamanuel.com? to assemble the MG-II

[jbelanger]

You really need to register on the msextra forum and post there. And you want to look at the documentation there also.

Jean

[jrods2]

cannot register for the http://www.msextra.com/forums/index.php. Will not accept my info. cannot contact admin because it does not allow Hotmail. I tried to register to one of the sites listed and could not get it to accept info either. Thanks Jerrold

[jbelanger]

Well that's a problem because you will need to register there. The forum here is only for my products; any Megasquirt support has to be done at one of the Megasquirt forums (and the msextra forum is the best place for that).

Jean

[dontz125]

jsmcortina is a member here and the admin over at MSExtra. Perhaps sending him a PM from here explaining the situation might help.

[jrods2]

Thank you for the reply. was what I needed. Don't go to far, more than likely will need this forums help again. Got the power supply on MS3 done & everything is spot on.

[jrods2]

hypperterm was checked and verified
this is what I get when I try to download the MS-1/II Download

2.00

MS-1/MS-II Embedded code update utility
For pre-Extra MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open.

help info in MS-I/MS-II Embedded code update utility
Downloading New Code
You can Only known to work with MegaSquirt-II…
You can
Communication port number
Communication rate
Verbosity
Logging…
hyperterm was checked & verified

[jrods2]

HERE'S WHERE I HAVE GOTTEN TO:
hypperterm was checked and verified
this is what I get when I try to download the MS-1/II Download

2.00

MS-1/MS-II Embedded code update utility
For pre-Extra MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open.

help info in MS-I/MS-II Embedded code update utility
Downloading New Code
You can Only known to work with MegaSquirt-II…
You can
Communication port number
Communication rate
Verbosity
Logging…
hyperterm was checked & verified


LSI Softmodem Version 2.2.89.2

ERROR
Added "Read Signature" command to file menu. It goes

through
ERROR
all the command signature and version characters, attempting
ERROR
to see what firmware is installed on the processor.
ERROR
Added "msu" (MegaSquirt Update) file format so that codein
ERROR

NO CARRIER

ERROR

LSI Softmodem Version 2.2.89.2

ERROR

ERROR
I GOT THIS WHEN I TURNED THE SWITCH OFF THEN BACK

ON:
€€€€€€€€€€€À€€ÀÀÀÀÀÀ

€ÀÀÀÀÀÀÀÀÀàÀàààààààààààààààðàðàøàðàðøðððððððøðððø
ðøøøøøøüøüøøøøüøøüøøüüüøøüüøþüþüüüüþüþþþþüüþþþþþþ

þ þþ þ þ þþ þ þþ þ

I HAVE TO ASSUME THAT HYPERTERM IS WORKING DUE TO THE ABOVE, FOR SOME REASON IT'S JUST NOT GETTING THE PROPER CODE

[jbelanger]

Please don't cross-post here and on the msextra forum. As I said, this is an MS issue and you are already getting the best answers you're going to get on the msextra forum.

Jean