Mega Squirt II Programmable EMS, PC3.0

Main site: http://jbperf.com/index.html

Mega Squirt II Programmable EMS, PC3.0

Postby jrods2 » Wed Nov 12, 2014 12:15 pm

Finished JimStim & every thing works as required. Starting MG-II assembly, Are there better assembly instructions(like the JimStim) than the one at www.megamanuel.com? to assemble the MG-II
building ms2 & jimstim for my use. 66 ford galaxie 390 cid Paxton super charger @ 20 psi
jrods2
 
Posts: 19
Joined: Sun Nov 09, 2014 2:35 pm
Location: palmdale ca

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jbelanger » Wed Nov 12, 2014 12:20 pm

You really need to register on the msextra forum and post there. And you want to look at the documentation there also.

Jean
Image
jbelanger
 
Posts: 3633
Joined: Sat Oct 03, 2009 12:24 pm
Location: Quebec, Canada

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jrods2 » Wed Nov 12, 2014 2:43 pm

cannot register for the http://www.msextra.com/forums/index.php. Will not accept my info. cannot contact admin because it does not allow Hotmail. I tried to register to one of the sites listed and could not get it to accept info either. Thanks Jerrold
building ms2 & jimstim for my use. 66 ford galaxie 390 cid Paxton super charger @ 20 psi
jrods2
 
Posts: 19
Joined: Sun Nov 09, 2014 2:35 pm
Location: palmdale ca

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jbelanger » Wed Nov 12, 2014 3:10 pm

Well that's a problem because you will need to register there. The forum here is only for my products; any Megasquirt support has to be done at one of the Megasquirt forums (and the msextra forum is the best place for that).

Jean
Image
jbelanger
 
Posts: 3633
Joined: Sat Oct 03, 2009 12:24 pm
Location: Quebec, Canada

Re: Mega Squirt II Programmable EMS, PC3.0

Postby dontz125 » Wed Nov 12, 2014 7:16 pm

jsmcortina is a member here and the admin over at MSExtra. Perhaps sending him a PM from here explaining the situation might help.
dontz125
 
Posts: 199
Joined: Mon Feb 22, 2010 10:27 pm

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jrods2 » Mon Nov 17, 2014 1:35 pm

Thank you for the reply. was what I needed. Don't go to far, more than likely will need this forums help again. Got the power supply on MS3 done & everything is spot on.
building ms2 & jimstim for my use. 66 ford galaxie 390 cid Paxton super charger @ 20 psi
jrods2
 
Posts: 19
Joined: Sun Nov 09, 2014 2:35 pm
Location: palmdale ca

MS2V3 DOWNLOAD

Postby jrods2 » Sun Nov 30, 2014 9:20 pm

hypperterm was checked and verified
this is what I get when I try to download the MS-1/II Download

2.00

MS-1/MS-II Embedded code update utility
For pre-Extra MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open.

help info in MS-I/MS-II Embedded code update utility
Downloading New Code
You can Only known to work with MegaSquirt-II…
You can
Communication port number
Communication rate
Verbosity
Logging…
hyperterm was checked & verified
building ms2 & jimstim for my use. 66 ford galaxie 390 cid Paxton super charger @ 20 psi
jrods2
 
Posts: 19
Joined: Sun Nov 09, 2014 2:35 pm
Location: palmdale ca

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jrods2 » Sun Nov 30, 2014 9:51 pm

HERE'S WHERE I HAVE GOTTEN TO:
hypperterm was checked and verified
this is what I get when I try to download the MS-1/II Download

2.00

MS-1/MS-II Embedded code update utility
For pre-Extra MS-II:
1) Short the "B/LD" jumper on the MS-II board.
2) Power cycle MS-II.
3) File->Open.

help info in MS-I/MS-II Embedded code update utility
Downloading New Code
You can Only known to work with MegaSquirt-II…
You can
Communication port number
Communication rate
Verbosity
Logging…
hyperterm was checked & verified


LSI Softmodem Version 2.2.89.2

ERROR
Added "Read Signature" command to file menu. It goes

through
ERROR
all the command signature and version characters, attempting
ERROR
to see what firmware is installed on the processor.
ERROR
Added "msu" (MegaSquirt Update) file format so that codein
ERROR

NO CARRIER

ERROR

LSI Softmodem Version 2.2.89.2

ERROR

ERROR
I GOT THIS WHEN I TURNED THE SWITCH OFF THEN BACK

ON:
€€€€€€€€€€€À€€ÀÀÀÀÀÀ

€ÀÀÀÀÀÀÀÀÀàÀàààààààààààààààðàðàøàðàðøðððððððøðððø
ðøøøøøøüøüøøøøüøøüøøüüüøøüüøþüþüüüüþüþþþþüüþþþþþþ

þ þþ þ þ þþ þ þþ þ

I HAVE TO ASSUME THAT HYPERTERM IS WORKING DUE TO THE ABOVE, FOR SOME REASON IT'S JUST NOT GETTING THE PROPER CODE
building ms2 & jimstim for my use. 66 ford galaxie 390 cid Paxton super charger @ 20 psi
jrods2
 
Posts: 19
Joined: Sun Nov 09, 2014 2:35 pm
Location: palmdale ca

Re: Mega Squirt II Programmable EMS, PC3.0

Postby jbelanger » Sun Nov 30, 2014 10:08 pm

Please don't cross-post here and on the msextra forum. As I said, this is an MS issue and you are already getting the best answers you're going to get on the msextra forum.

Jean
Image
jbelanger
 
Posts: 3633
Joined: Sat Oct 03, 2009 12:24 pm
Location: Quebec, Canada


Return to General

Who is online

Users browsing this forum: No registered users and 2 guests